1.1 This guide provides guidance for the types and extent of testing that would be involved in characterizing the physical and chemical nature of spent nuclear fuel (SNF) in support of its interim storage, transport, and disposal in a geologic repository. This guide applies primarily to commercial light water reactor (LWR) spent fuel and spent fuel from weapons production, although the individual tests/analyses may be used as applicable to other spent fuels such as those from research reactors, test reactors, molten salt reactors and mixed oxide (MOX) spent fuel. The testing is designed to provide information that supports the design, safety analysis, and performance assessment of a geologic repository for the ultimate disposal of the SNF.
1.2 The testing described includes characterization of such physical attributes as physical appearance, weight, density, shape/geometry, degree, and type of SNF cladding damage. The testing described also includes the measurement/examination of such chemical attributes as radionuclide content, microstructure, and corrosion product content, and such environmental response characteristics as drying rates, oxidation rates (in dry air, water vapor, and liquid water), ignition temperature, and dissolution/degradation rates. Not all of the characterization tests described herein must necessarily be performed for any given analysis of SNF performance for interim storage, transportation, or geological repository disposal, particularly in areas where an extensive body of literature already exists for the parameter of interest in the specific service condition.
1.3 It is assumed in formulating the SNF characterization activities in this guide that the SNF has been stored in an interim storage facility at some time between reactor discharge and dry transport to a repository. The SNF may have been stored either wet (for example, a spent fuel pool), or dry (for example, an independent spent fuel storage installation (ISFSI)), or both, and that the manner of interim storage may affect the SNF characteristics.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1.1 This guide provides guidance for the types and extent of testing that would be involved in characterizing the physical and chemical nature of spent nuclear fuel (SNF) in support of its interim storage, transport, and disposal in a geologic repository. This guide applies primarily to commercial light water reactor (LWR) spent fuel and spent fuel from weapons production, although the individual tests/analyses may be used as applicable to other spent fuels such as those from research reactors, test reactors, molten salt reactors and mixed oxide (MOX) spent fuel. The testing is designed to provide information that supports the design, safety analysis, and performance assessment of a geologic repository for the ultimate disposal of the SNF.
1.2 The testing described includes characterization of such physical attributes as physical appearance, weight, density, shape/geometry, degree, and type of SNF cladding damage. The testing described also includes the measurement/examination of such chemical attributes as radionuclide content, microstructure, and corrosion product content, and such environmental response characteristics as drying rates, oxidation rates (in dry air, water vapor, and liquid water), ignition temperature, and dissolution/degradation rates. Not all of the characterization tests described herein must necessarily be performed for any given analysis of SNF performance for interim storage, transportation, or geological repository disposal, particularly in areas where an extensive body of literature already exists for the parameter of interest in the specific service condition.
1.3 It is assumed in formulating the SNF characterization activities in this guide that the SNF has been stored in an interim storage facility at some time between reactor discharge and dry transport to a repository. The SNF may have been stored either wet (for example, a spent fuel pool), or dry (for example, an independent spent fuel storage installation (ISFSI)), or both, and that the manner of interim storage may affect the SNF characteristics.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
5.1 In order to demonstrate conformance to regulatory requirements and support the post-closure repository performance assessment information is required about the attributes, characteristics, and behavior of the SNF. These properties of the SNF in turn support the transport, interim storage, and repository pre-closure safety analyses, and repository post-closure performance assessment.
In the United States, the interim dry storage of commercial LWR SNF is regulated per the Code of Federal Regulations, Title 10, Part 72, which requires that the cladding must not sustain during the interim storage period any “gross” damage sufficient to release fuel from the cladding into the container environment. In other countries, the appropriate governing body will set regulations regarding interim dry storage of commercial LWR SNF.
However, cladding damage insufficient to allow the release of fuel during the interim storage period may still occur in the form of small cracks or pinholes that can develop into much larger defects. These cracks/pinholes could be sufficient to classify the fuel as “failed fuel” or “breached fuel” per the definitions given in Section 3 for repository disposal purposes, because they could allow contact of water vapor or liquid with the spent fuel matrix and thus provide a pathway for radionuclide release from the waste form.
Therefore SNF characterization should be adequate to determine the amount of “failed fuel” for either usage as required. This could involve the examination of reactor operating records, ultrasonic testing, sipping, and analysis of the residual water and drying kinetics of the spent fuel assemblies or canisters.
5.2 Regulations in each country may contain constraints and limitations on the chemical or physical (or both) properties and long-term degradation behavior of the spent fuel and HLW in the repository. Evaluating the design and performance of the waste form (WF), waste packaging (WP), and the rest of the engineered barrier system (EBS) with respect to these regulatory constraints requires knowledge of the chemical/physical characteristics and degradation behavior of the SNF that could be provided by the testing and data evaluation methods provided by this guide, using the United States as an example, as follows:
5.3 The enhanced chemical reactivity and degraded condition of corroded/damaged uranium metal-based SNF must be accounted for in both the pre-closure safety analyses and the post-closure performance assessment of the geologic repository. An example of this would be the potential for pyrophoric behavior in uranium metal-based SNF (see Guide C1454).
Due to the combustibility of the metallic uranium or uranium hydride (or both), and the enhanced aqueous dissolution rates for the exposed uranium metal, the potential for enhanced chemical activity or pyrophoric behavior must be factored into the repository or interim storage facility safety analyses, and assessments of the potential for radionuclide releases from the repository site boundary after repository closure.
5.4 Characterization of several key properties of SNF may be required to support the design and performance analyses of both repository above-ground SNF receipt and lag storage facilities, the WP into which the SNF is placed, and the subsurface permanent emplacement drift EBS.
Metallic uranium-based nuclear fuel has been widely used in nuclear reactors; sometimes for commercial reactors (for example, Magnox) but more often in plutonium and tritium production reactors. The manner of discharge of metallic uranium SNF from these production reactors, and/or the manner of temporary wet storage of that portion of the spent fuel that was not reprocessed has in many instances resulted in significant corrosion and mechanical damage to the SNF assemblies.
This damage has resulted in the direct exposure of the metallic uranium to the basin water. The relatively high chemical reactivity of uranium in contact with water can result in significant physical damage to the assemblies as the result of corrosion product buildup, and the creation in the exposed fuel surface and fuel matrix of uranium hydride inclusions which in turn further increase the chemical activity of the material.
The reaction of this spent fuel with air, water vapor, or liquid water can introduce a significant heat source term into design basis events. In order to support the evaluation of these events, the physical condition (that is, the degree of optically/visually observable damage), the chemical oxidation kinetics, the ignition characteristics, and radionuclide release characteristics of the SNF should be investigated.
Failed to load document history.
| Publish Date | Document Id | Type | View |
|---|